SAFETY DATA SHEET
Conductive Epoxy - Part B (Hardener)
1. IDENTIFICATION
Product Identifiers
Product Name:
CIRCUITWORKS® CONDUCTIVE EPOXY - Part B (Hardener)
Other Names:
Silver conductive epoxy
Product Number(s):
CW2400, CW2400BLK PART B, CW2400J, PEL16043,16043
CAS Number:
Recommended use of the chemical and restriction on use
Where and restrictions (eg. Laboratory use.)
Company Details
ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia(07) 4773 9444www.proscitech.com
11 Carlton Street
KIRWAN QLD 4817
Australia(07) 4773 9444www.proscitech.com
Emergency Contact Details
ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia(07) 4773 9444www.proscitech.com
11 Carlton Street
KIRWAN QLD 4817
Australia(07) 4773 9444www.proscitech.com
2. HAZARDS IDENTIFICATION
Classification of the substance or mixture
ACUTE TOXICITY (dermal) - Category 3
Percentage of the mixture consisting of ingredient(s) of unknown toxicity: 100%
Percentage of the mixture consisting of ingredient(s) of unknown toxicity: 100%
Label Elements
Signal Words
Danger
Hazard Statement(s)
Toxic in contact with skin.
Precautionary Statement(s)
Prevention: Wear protective gloves. Wear protective clothing.
Response: IF ON SKIN: Take off immediately all contaminated clothing and wash it before reuse. Wash with plenty of soap and water. Call a POISON CENTER or physician if you feel unwell.
Storage: Store locked up.
Disposal: Dispose of contents and container in accordance with all local, regional, national and international regulations. : None known.
Response: IF ON SKIN: Take off immediately all contaminated clothing and wash it before reuse. Wash with plenty of soap and water. Call a POISON CENTER or physician if you feel unwell.
Storage: Store locked up.
Disposal: Dispose of contents and container in accordance with all local, regional, national and international regulations. : None known.
Primary route(s) of entry
Non Stated
Human Health
Inhalation:
Non Stated
Ingestion:
Non Stated
Eyes:
Non Stated
Skin:
Non Stated
Environment
Non Stated
3. COMPOSITION/INFORMATION ON INGREDIENTS
Name
CAS No.
Content (w/w)
Classification
3,6-diazaoctanethylenediamin
112-24-3
≤6.8
Not Available
4. FIRST AID MEASURES
Ingestion
Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Inhalation
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours.
Skin Contact
Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Continue to rinse for at least 10 minutes. Get medical attention. If necessary, call a poison centre or physician. Wash clothing before reuse. Clean shoes thoroughly before reuse.
Eye Contact
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention.
Other Information
Most important symptoms/effects, acute and delayed
Potential acute health effects.
Eye contact: May cause severe eye irritation.
Inhalation: No known significant effects or critical hazards.
Skin Contact: Toxic in contact with skin.
Ingestion: Harmful if swallowed.
Over-exposure signs/symptoms.
Eye contact: irritation
redness
watering
Inhalation: respiratory tract irritation
coughing
Skin Contact: pain or irritation
redness
blistering may occur
Ingestion: stomach pains
Indication of immediate medical attention and special treatment needed, if necessary:
Notes to Physician: In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours.
Specific Treatments: No specific treatment.
Protection of First-aiders: No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves.
Potential acute health effects.
Eye contact: May cause severe eye irritation.
Inhalation: No known significant effects or critical hazards.
Skin Contact: Toxic in contact with skin.
Ingestion: Harmful if swallowed.
Over-exposure signs/symptoms.
Eye contact: irritation
redness
watering
Inhalation: respiratory tract irritation
coughing
Skin Contact: pain or irritation
redness
blistering may occur
Ingestion: stomach pains
Indication of immediate medical attention and special treatment needed, if necessary:
Notes to Physician: In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours.
Specific Treatments: No specific treatment.
Protection of First-aiders: No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves.
5. FIREFIGHTING MEASURES
Suitable extinguishing equipment
Use an extinguishing agent suitable for the surrounding fire.
HAZCHEM
Special protective equipment and precautions for fire fighters
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
For Non-emergency Personnel: No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Do not breathe vapour or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment.
For emergency responders: If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For nonemergency personnel".
For emergency responders: If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For nonemergency personnel".
Environmental precautions
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air).
Methods and materials for containment and clean up
Small Spill: Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor.
Large Spill: Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal
Large Spill: Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal
7. HANDLING AND STORAGE
Precautions for safe handling
Protective Measures: Put on appropriate personal protective equipment (see Section 8). Do not get in eyes or on skin or clothing. Do not breathe vapour or mist. Do not ingest. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container.
Advice on General Occupational Hygiene: Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures
Advice on General Occupational Hygiene: Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures
Conditions for safe storage
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Exposure Standards
Material
TWA ppm
TWA mg/m3
STEL ppm
STEL mg/m3
3,6-diazaoctanethylenediamin
1ppm 8 hours
-
-
Engineering controls
Good general ventilation should be sufficient to control worker exposure to airborne contaminants.
Personal protective equipment
Eye and face protection
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with sideshields.
Skin protection
Hand Protection: Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated.
Other skin protection: Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.
Other skin protection: Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.
Respiratory protection
Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.
9. PHYSICAL AND CHEMICAL PROPERTIES
General information
Appearance
Liquid (paste)
Odour
Amine like.
pH
Not available.
Vapour Pressure
<0.013 kPa (<0.1 mm Hg) [room temperature]
Density
Not available.
Boiling Point
Not available.
Melting Point
Not available.
Solubility
Not available.
Specific Gravity of Density
Not available.
Flash Point
Closed cup: >93.3°C (>199.9°F) [Setaflash.]
Flammable (Explosive) Limits
Not available.
Ignition Temperature
Not available.
Formula
Not available.
10. STABILITY AND REACTIVITY
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Chemical stability
The product is stable.
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Conditions to avoid
No specific data.
Incompatible materials
No specific data.
11. TOXICOLOGICAL INFORMATION
Acute effects
3,6-diazaoctanethylenediamin LD50 Dermal Rabbit 805 mg/kg
LD50 Oral Rat 2500 mg/kg
LD50 Oral Rat 2500 mg/kg
Eye contact
May cause severe eye irritation.
Skin contact
Toxic in contact with skin
Ingestion
Harmful if swallowed.
Inhalation
No known significant effects or critical hazards
Toxicity and irritation
Acute toxicity estimates
Route ATE value
Oral 2500 mg/kg
Dermal 805 mg/kg
Route ATE value
Oral 2500 mg/kg
Dermal 805 mg/kg
12. ECOLOGICAL INFORMATION
Ecotoxicity
No known significant effects or critical hazards.
Persistence and degradability
Not available.
Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
3,6-diazaoctanethylenediamin -1.66 to -1.4 - Low
3,6-diazaoctanethylenediamin -1.66 to -1.4 - Low
Other adverse effects
No known significant effects or critical hazards.
13. DISPOSAL CONSIDERATIONS
General information
The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.
14. TRANSPORT INFORMATION
ADG label required
HAZCHEM
UN Number
Not regulated.
Proper shipping name
Adhesive, sealants
Transport hazard class
N/a
Packing group
n/a
Environmental hazard
No
Special precautions for users
N/a
Additional information
Reportable quantity: 1333.3 lbs / 605.33 kg [39. 003 gal / 147. 64 L] Package sizes shipped in quantities less than the product reportable quantity are not subject to the RQ (reportable quantity) transportation requirements
15. REGULATORY INFORMATION
Poisons Schedule Number
Not applicable.
Other Information
Nil
16. OTHER INFORMATION
SDS preparation date
1 April 2025
Comments
References
SDS CIRCUITWORKS® CONDUCTIVE EPOXY - Part B (Hardener) chrome-extension://efaidnbmnnnibpcajpcglclefindmkaj/https://www.2spi.com/catalog/documents/05000-partB-CircuitWorks-CW2400-4-22-2015.pdf 11/13/2018
This Safety Data Sheet (SDS) has been prepared in compliance with the Preparation of Safety Data Sheets for Hazardous Chemicals Code of Practice February 2016. It is the user's responsibility to determine the suitability of this information for adoption of necessary safety precautions. The information published in this SDS has been compiled from the publications listed in Section 16: to the best of our ability and knowledge these publications are considered accurate. We reserve the right to revise Safety Data Sheets as new information becomes available. Copies may be made for non-profit use.